Sea-Bird Electronics SBE 38 Bedienungsanleitung PDF herunterladen (Seite 53)

Appendix III: Command Summary SBE 45

Appendix III: Command Summary

CATEGORY COMMAND DESCRIPTION

Status DS

Display status.

Baud=x

x= baud rate (1200, 2400, 4800, 9600, 19200,

or 38400). Default 4800.

OutputFormat=x

x=0 (default): Output order is temperature,

conductivity, salinity, sound velocity.

x=1: Suppress space before conductivity output.

x=2: Reverse conductivity and salinity order (not for

use with Seasave, SBE Data Processing, or optional

Interface Box).

OutputCond=x

x=Y (default): Output conductivity (S/m) with data.

x=N: Do not.

OutputSal=x

x=Y: Output salinity (psu) with data.

x=N (default): Do not.

OutputSV=x

x=Y: Output sound velocity (m/sec) with data,

calculated as defined by SVAlgorithm=.

x=N (default): Do not.

SVAlgorithm=x

x=C (default): Calculate sound velocity as Chen

and Millero.

x=W: Calculate sound velocity as Wilson.

NCycles=x

x = A/D cycles to average per sample (default=4).

Setup

Quit session and place MicroTSG in quiescent (sleep)

state. Sampling stops. Applicable only if PCB J1

jumper in Normal position.

Interval=x

x= interval (seconds) between samples (maximum

32767). Minimum time between samples determined

by NCycles=, desired parameters (salinity, etc.), and

baud rate.

AutoOff=x

(Functional only if J1 jumper in Normal position)

x=Y: Go to sleep (enter quiescent state) if 2 minutes

have elapsed without receiving a command or without

sampling data.

x=N: Do not automatically go to sleep.

J1 jumper - Normal

AutoRun=N

SingleSample=

Y or N

Wake up when Connect on Toolbar clicked or Enter

key pressed while in quiescent (sleep) state, wait for a

command.

J1 jumper - Normal

AutoRun=Y

SingleSample=N

Wake up when Connect on Toolbar clicked or Enter

key pressed while in quiescent (sleep) state, sample at

rate specified by Interval=. To stop sampling and get

S> prompt, type Stop and press Enter key.

J1 jumper - Normal

AutoRun=Y

SingleSample=Y

Wake up when Connect on Toolbar clicked or Enter

key pressed while in quiescent (sleep) state, take and

output a single sample, automatically go to sleep. To

wake up and get S> prompt, type Stop and press

Enter key.

J1 jumper - Autopower

AutoRun=N

SingleSample=Y or N

Wake up when power applied, wait for a command.

J1 jumper - Autopower

AutoRun=Y

SingleSample=N

Wake up when power applied, sample at rate specified

by Interval= until power removed. Required settings

for running MicroTSG in 3-wire (power, ground,

transmit) configuration or with Interface Box.

J1 jumper - Autopower

AutoRun=Y

SingleSample=Y

Wake up when power applied, take and output a

single sample. Wait for another command until

power removed.

Start sampling, as defined by SingleSample=

and Interval=. Applicable if AutoRun=N, or

AutoRun=Y and you previously sent Stop to

stop sampling.

Operating

PCB’s J1

jumper interacts

with these

commands:

• Autopower –

pins 1 and 2

• Normal –

pins 2 and 3

Stop

Stop sampling.

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 103 104

Kommentare zu diesen Handbüchern

Keine Kommentare

Sea-Bird Electronics SBE 38 Bedienungsanleitung Seite 53

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Messen, Testen & Steuern Sea-Bird Electronics SBE 38